S460NL & S460ML

S460NL & S460ML

Unlike any other structural specification under EN10025 S460 material does not have any direct equivalents in ASTM or Shipbuilding (ABS/BV/LR) designations.

S460NL & S460ML is used in a number of offshore and onshore applications e.g. legs supports for a jack up platform offshore and as mooring piles for a LNG onshore terminal.

S460NL
A normalised material with a minimum yield strength of 450 N/mm2 that has been impact tested at -50°C. S460NL is produced under European designation EN10025-3.

S460ML
A thermo-mechanically rolled material with a minimum yield strength of 450 N/mm2 that has been impact tested at -50°C. S460ML is produced under European designation EN10025-4 (TMCP).

are able to supply a wide range of S460 material (in both normalised and TMCP conditions), our material ranges from 6mm to 80mm thick and up to 3 metre’s wide and 12 metre’s in length.

Chemical Composition of S460NL & S460ML

Grade	C	Si	Mn	P	S	N	Al	Cu	Cr	Ni	Mo	Nb	V	Ti
S460NL	0.20	0.60	1.00/1.70	0.025	0.020	0.025	0.020	0.55	0.30	0.80	0.10	0.050	0.20	0.05
S460ML	0.16	0.60	1.70	0.025	0.025	0.025	0.020	0.55	0.30	0.80	0.20	0.05	0.12	0.05

Main chemical composition in EN 10113-3 S460ML steel is carton max 0.16, silicon max 0.60, manganese max 1.70, phosphorus max 0.025, Sulphur max 0.02, chromium max 0.30. More detailed information about S460ML steel, please refer to the down table:

Grade	C max	Si max	Mn max	P max	S max	N max	AL max	Nb max	V max	Ti max	Cr max	Ni max	Mo max	Cu max	CEV max
S420ML	0.16%	0.60%	1.70%	0.025%	0.02%	0.025%	0.02%	0.05%	0.12%	0.05%	0.30%	0.80%	0.20%	0.55%	0.48%

EN10113-3 S460ML is a technical delivery conditions for thermomechanical rolled weldable fine grain structural steels.S means the structural steel, M means the delivery condition.Capital letter L for the quality with specified minimum values of values of impact energy at temperature not lower than -50 degree.

Temperature	-50	-40	-30	-20	-10	0	20
Notch impact test. Min. absorbed energy	27	31	40	47	51	55	63

 

Nominal thickness(mm)	to 16	16-40	40-63	63-80	80-100	100-120
ReH-Minimun yield strength(Mpa)	460	440	430	410	400	385

 

Nominal thickness(mm)	to 40	40-63	63-80	80-100	100-120
Rm-Tensile strength(Mpa)	540-720	530-710	510-690	500-680	490-660
Nominal thickness(mm)	-
A-Minimum elongation  Lo=5,65√So(%)	17

S460NL & S460ML Unlike any other structural specification under EN10025 S460 material does not have any direct equivalents in ASTM or Shipbuilding (ABS/BV/LR) designations. S460NL & S460ML is used in a number of offshore and onshore applications e.g. legs supports for a jack up pla